![]() ![]() Links to sources/information is okay in limited situations where it directly relates to conversation, but posters should not be regularly posting the same external sites/other subreditts over and over again. The intention of the sub is to help posters here.The intention of the sub is to help posters, not to promote a brand. Making an occasional mention of a brand when relevant to the discussion is fine.but repeatedly posting nothing but a brand over and over without any further information/discussion is not acceptable. No attempting to solicit customers, no offers to give quotes or asking to private message. No affiliate links, no links that earn you money/anything, no self-promotion, no promotion of your business, no promotion of your subreddit.It's okay to disagree, but please refrain from being needlessly rude. Be gracious and up vote posts and comments liberally.If you are linking to a specific product page provide the full, direct URL. External links are permitted so long as they aren't spam, personal blogs, or memes.Home security can be anything from a full blown monitored service and a surveillance system to simple things like having a double cylinder deadbolt on your front door.Īny aspect about home security can be discussed here: alarms, surveillance, locks, personal protection, etc. This subreddit is a place where you can discuss it. You must repeat by entering your code and pressing the ENTER key for a second time in order to silence the alarm.Protecting yourself, your loved ones, and your home is important. To silence the alarm, enter your code and then press the ENTER key. After your system is off-line, press and hold the oval button on the face of the smoke detector to trigger the alarm. BE SURE TO CALL US AT 51 DURING NORMAL BUSINESS HOURS TO TAKE YOUR ACCOUNT OFF-LINE PRIOR TO TRIGGERING THE SMOKE DETECTOR. IMPORTANT: The smoke detector must be triggered in order to complete the process. Put the unit back onto the base by turning clockwise. When installing the new 3-Volt lithium battery, MAKE SURE TO INSTALL THE NEGATIVE END FIRST (See Figure 3 above), then push down on the positive end. Remove the battery by pulling up on the (+) positive end first. ![]() Next, open the 3-Volt lithium battery cover by prying it with a regular screwdriver. Replace with a new 9-Volt Alkaline battery. Open the 9-Volt battery cover with a Phillips head screwdriver. To replace the batteries, first remove the smoke detector from the base by turning it counterclockwise. Replace the cover by placing it on the ‘hinge’ first and then closing it and snapping it back onto the base. The battery holder is very tight to the battery and you may have to apply a good amount of pressure to insert the battery inside the blue battery holder as well as pushing it down inside the holder. Insert the battery with the positive (+) terminal toward the right side of the Motion Sensor. The battery holder is very tight to the battery, and the batteries may have to be pried out with a flat head screwdriver. The cover will open toward the ‘hinge’ on the opposite side. To replace the batteries, insert a flat head screwdriver in the center of the base between the seams and push and twist at the same time to open the cover. On the newer version Gemini panels (Version V31G or greater, installed or upgraded after Jan 1, 2021), you must enter your user code and then press ‘RESET’. When completed, go the keypad and press the ‘RESET’ button. If it doesn’t close, try reversing the cover and snapping it back in place. Replace the cover by snapping it back onto the base. Slide the battery under the two brass prongs and press into the holder (on older versions) or place the battery on top of the 2 brass prongs and press into the holder (on newer versions). INSERT THE NEW BATTERY: Observe polarity with the positive (+) side facing up. REMOVE THE OLD BATTERY: CAUTION : Place your thumb on the battery with some pressure on it and hold it there while inserting a small screwdriver to pry out the battery (in order to prevent the battery holder from separating from the board). The battery must be replaced in the same position! IMPORTANT: BEFORE REMOVING THE OLD BATTERY, OBSERVE THE BATTERY AND NOTE THE 2 BRASS PRONGS AND THEIR POSITION ON TOP OR BELOW THE BATTERY. To replace the battery, remove the cover by inserting a small screwdriver into the slot on the shorter side of the transmitter, twisting while applying upward pressure. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |